Writing a Blister Film Specification: What Belongs on the Sheet
By the Green Medical Packing engineering team

Why the sheet matters more than the datasheet
A supplier datasheet describes a product family. A purchase specification describes the material you are buying and the conditions under which you will accept it. When the two are confused, quality discussions turn into arguments about interpretation rather than measurements.
The specification sheet is also what a notifying body, an auditor or a second supplier will read. If it names the material, the test method and the acceptance criterion, three different parties can reach the same result. If it names only the material, none of them can.
Identification block
Start with the administrative facts that make the document traceable:
- Document number and revision, with an effective date
- Material name and grade, plus the supplier's own product code
- Intended use, stated as the product and pack format (for example, PVC rigid film for thermoformed blister cavities for solid oral dosage)
- Regulatory basis, listing the compendial monographs the material is expected to meet
- Linked documents: drawing of the pack, lidding specification, artwork reference
A revision table belongs here as well. A specification without revision control cannot be audited, because no one can tell which version was in force for a given batch.
Material and compliance basis
State the polymer or structure, and the compliance statements expected per delivery. For a PVC rigid film that usually means the USP <661> and EP 3.1/3.2 statements, plus the migration or food-contact statement required by the destination market. For foil, name the alloy family, temper and lacquer type rather than a generic "aluminium foil".
Phrase compliance as a document requirement: which statement, from whom, at what frequency, in which language. "Compliant with USP" is not a specification line; "USP <661> statement per lot, issued by the manufacturer" is.
Dimensional requirements
Dimensions are where most disputes start, because a single nominal figure invites a different interpretation on each side.
| Parameter | How to state it | Test method to name |
|---|---|---|
| Thickness or gauge | Nominal plus tolerance, and the measurement points | Micrometer, number of readings, position across the web |
| Width | Nominal with slit tolerance and edge condition | Measured at three positions per roll |
| Reel | Core diameter, outside diameter, winding direction, roll weight | Stated per roll, not per pallet |
| Camber | Maximum deviation over a stated length | Measured against a straight edge |
| Splice | Number permitted per roll, splice type and marking | Visual, with splice flagged |
Tolerance without a method is an opinion. The method is what makes the tolerance enforceable, and it is the first thing a supplier will ask about when a claim is raised.
Mechanical and optical properties
For rigid film, the properties that affect forming and line running are tensile strength and elongation, impact resistance, coefficient of friction and haze. Each needs a method reference, a specimen orientation and an acceptance range.
Coefficient of friction is the one buyers most often omit and then complain about, because a film that meets its gauge and barrier targets can still jam a high-speed line. State static and kinetic values separately, name the surfaces being tested (film to film, film to metal) and give the test speed.
Barrier requirements
Write the barrier target as a number with a method, not as a material name. Water vapour transmission rate at 38 °C and 90 % relative humidity, with the test method and the reported units, is a specification. "High barrier" is a description.
Two details decide whether the number means anything: whether the value refers to flat material or to a formed cavity, and the conditioning time before testing. Deep cavities transmit more than flat sheet, and comparison between suppliers fails when one reports flat and the other reports formed.
For foil, add a pinhole acceptance limit per unit area and the detection method, since barrier in a converted laminate depends on foil continuity. The methods and limits are set out in PTP aluminium foil pinholes: causes and limits.
Heat seal window, stated against the lidding
Seal performance belongs to the pair, not to the film alone. The specification should name the lidding material it is qualified against, then state the seal temperature range, pressure, dwell time and the resulting peel strength range with its test method.
If the customer changes lidding supplier, the seal block has to be re-validated. Recording the qualified pair prevents the assumption that any foil with the same gauge will seal the same way. Peel and burst limits for the pair are covered in blister seal strength: peel and burst limits.
Documentation per delivery
List what arrives with each shipment, so receiving inspection has something to check against:
- Certificate of analysis for the lot, with the measured values, not only pass or fail
- Compliance statements current for the destination market
- Roll label data: material code, lot, gauge, width, length, weight, date of manufacture
- Change-control notification requirements, including the notice period before a formulation or raw-material supplier change
Sampling and acceptance
Acceptance criteria are only useful with a sampling plan. State the sample size per lot, the number of rolls sampled, the acceptance number and what happens on a non-conformance: retest, concession or rejection, and who decides.
Buyers who skip this section end up negotiating each deviation separately, usually under time pressure.
Common omissions
- No revision control, so the current version is unclear
- Tolerance stated without a test method or measurement position
- Barrier target given as a material name
- Seal window written against no specific lidding
- No splice allowance, which becomes a line stoppage later
- No change-control clause, so formulation changes arrive without notice
A checklist to copy
1. Identification: document number, revision, material code, intended pack. 2. Compliance: which statements, per lot, in which market. 3. Dimensions: nominal, tolerance, method, measurement positions. 4. Mechanical and optical: tensile, elongation, impact, friction, haze. 5. Barrier: value, units, method, flat or formed, conditioning. 6. Seal: qualified lidding, temperature, pressure, dwell, peel range. 7. Documentation: certificate of analysis content, labels, change control. 8. Acceptance: sampling plan, acceptance number, deviation route.
Next step
Send us the pack drawing and the values you already use, and our engineers will return a specification draft with the methods and acceptance criteria filled in for the material you are considering. Material options are listed under standard blister PVC, high-barrier PVC, cold-form aluminium without PVC and PTP aluminium foil. Related reading: thickness tolerance in blister film and coefficient of friction on packaging lines.
Have questions about this topic?
Send your pack format and target market — our technical team replies within 48 hours.
Recommended materials
Materials referenced in this article

Standard Blister PVC
Versatile PVC sheets for thermoformed blister packaging
View specifications
High-Barrier PVC Films
Advanced moisture and oxygen barrier for extended shelf life
View specifications
Cold Forming Aluminum Without PVC
Eco-friendly PVC-free cold forming laminate for sustainable pharmaceutical packaging
View specifications

